I don't think is suggesting you would ONLY be able to address the dual mono channels as a pair. I think that your controller is like mine X-touch that don't use osculator at all but just midi.Īlso I didn't understand how to use substitution in osculator. Monitoring APCMini and changing the output of fader with your template nothing appears at atem mini fader. So: Monitoring X-touch it send out a midi picth weel control and raw data are E0 XX XX. My problem is for APCMini from AKAI that has CC from 49 to 56 on fader. I have an X-touch that no need to have any other software (osculator too) and just with midi driver I can pilot the ATEM mini fader and on/AFW buttons. You need an ATEM Mini, ATEM Mini Pro, ATEM Mini iso or ATEM Studio 4K with Fairlight support for this (as far as I know).įor me it's a workaround until ATEM OSC supports Fairlight Audio Sometimes I had to restart the ATEM Software control Panel to recognize the input. On my Mac ATEM Software control recognizes the output from Osculator and interprets them as explained. Hi dind't need to connect to ATEM Software.Ĭheck wether you have activatet Midi Control in the settings. I greatly appreciate what you are ding here ! It's a group of people from all over the world and started by Alex Lindsay of MacBreak/TWIT/ The Pixelcore. Let me know if that would help at in case either of you were interested, there is a group of AV folk who have been doing a morning ZOOM meetup called Office Hours. Since you do not have a switcher that supports fairlight audio to test on, if it would help we could schedule a time to do a screen share. Slider at 0: /atem/fairlight-audio/source/-65280/gain ,f 0.00 Slider at -inf: /atem/fairlight-audio/source/-65280/gain ,f -inf When I go to the message section OSCulator and in the ATEM application change slide the fader up or down on Cam1 I get the Following message in OSCulator: IN my case it is -65281 in my OSC Addresses list. ![]() I confirmed that Audition does the bank change correctly (though it populates the Mini with the right 8 channels as it considers it a full MC control surface).Ģ0200905: Added BANK RIGHT and BANK LEFT commands to A, buttons 9-10ĬONTROL TYPE CHANNEL NO.Same experience here. The Mini transposes its notes up an octave, so I programmed it with A#1,B1 instead. Kyle with Behringer support kindly pointed out the Bank Left and Bank Right commands (A#2,B2). I recently purchased the X-Touch Extender. Set Audition and Premiere Pro to use Mackie Control (MC), but leave your device in MIDI mode. Manually enter these settings using X-Touch Editor. MIDI Map for Adobe Audition and Premiere Pro ![]() TURN EN 8 CC 1 CC23 Relative3 - PAN PAN TRACK 8 TURN EN 7 CC 1 CC22 Relative3 - PAN PAN TRACK 7 TURN EN 6 CC 1 CC21 Relative3 - PAN PAN TRACK 6 TURN EN 5 CC 1 CC20 Relative3 - PAN PAN TRACK 5 TURN EN 4 CC 1 CC19 Relative3 - PAN PAN TRACK 4 TURN EN 3 CC 1 CC18 Relative3 - PAN PAN TRACK 3 TURN EN 2 CC 1 CC17 Relative3 - PAN PAN TRACK 2 TURN EN 1 CC 1 CC16 Relative3 - PAN PAN TRACK 1 PUSH EN 8 NOTE 1 D#1 - MOMENTARY SELECT TRACK 8īT 1 NOTE 1 G#-2 - MOMENTARY SOLO TRACK 1īT 2 NOTE 1 A-2 - MOMENTARY SOLO TRACK 2īT 3 NOTE 1 A#-2 - MOMENTARY SOLO TRACK 3īT 4 NOTE 1 B-2 - MOMENTARY SOLO TRACK 4īT 5 NOTE 1 C-1 - MOMENTARY SOLO TRACK 5īT 6 NOTE 1 C#-1 - MOMENTARY SOLO TRACK 6īT 7 NOTE 1 D-1 - MOMENTARY SOLO TRACK 7īT 8 NOTE 1 D#-1 - MOMENTARY SOLO TRACK 8 PUSH EN 7 NOTE 1 D1 - MOMENTARY SELECT TRACK 7 PUSH EN 6 NOTE 1 C#1 - MOMENTARY SELECT TRACK 6 PUSH EN 5 NOTE 1 C1 - MOMENTARY SELECT TRACK 5 PUSH EN 4 NOTE 1 B0 - MOMENTARY SELECT TRACK 4 PUSH EN 3 NOTE 1 A#0 - MOMENTARY SELECT TRACK 3 ![]() PUSH EN 2 NOTE 1 A0 - MOMENTARY SELECT TRACK 2 PUSH EN 1 NOTE 1 G#0 - MOMENTARY SELECT TRACK 1 Also, I haven't tested the F1-8 functions yet hopefully they will work.ĬONTROL TYPE CHANNEL NO. One challenge that I ran into was that Premier Pro (and presumably Audition) did not recognize many of the valid commands such as Solo, so I only had a few that I could map. I used a couple of Mackie Control/MIDI tables that I found online, and also used the MIDI Monitor window in Presonus Studio One to view the commands from the board while it was in MC mode. Apply the settings using the X-Touch Editor software (download from ). You'll want to copy this into a text editor so that the tabs will render correctly (or download the attached text file). In case it helps someone save time figuring it all out, here's my MIDI map for the Behringer X-Touch Mini.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |